Those planning to go to Autodesk University 2010 who have not spent much time on the AU Online site lately may not be aware that, unlike recent years, registration this year will not open in August but instead will start on September 14.
If you are not already registered at the AU Online site, do so now, and you will be able to register a week early, starting September 7.
Showing posts with label AU Online. Show all posts
Showing posts with label AU Online. Show all posts
August 05, 2010
December 18, 2009
AEC Content on the Ribbon - AU Tech Talk
October 19, 2013 Update: The links to the Autodesk website no longer work for me, so I assume that the AU Tech Talk content has been taken down. I have posted the contents of my article on putting AEC Content on the ribbon in this post.The December 2009 Edition of the AU Quarterly Newsletter is out. If you do not already receive the newsletter, you can do so by becoming a member of the AU Online site and requesting the newsletter in your profile, under the Preferences category. This edition includes a link to an AU Tech Talk article I wrote about accessing AEC Content from the ribbon. I had a chance to look into this topic more deeply since I last blogged about this topic.
The article is a fairly detailed tutorial (with pictures!) on how to customize a CUIX file to add a ribbon tool that "runs" a tool palette tool, enabling you to add your own custom AEC Content to a ribbon tab. You can access the AU Tech Talk page and look for my smiling face,
or go right to the article (sorry, there is a picture of me there, too).
October 26, 2009
Equal Lights Republished
A little over a year ago, I contributed an article to the AU Quarterly Newsletter on creating equal lights in Door/Window Assemblies, Curtain Walls and Curtain Wall Units. Unfortunately, when the AU Online site was overhauled last December, the links to articles from previous newsletters were lost. For those who never read the article and those who have forgotten its contents (including me), here is the article. If you are interested, a drawing file that has the Door/Window Assemblies used to generate the images below, along with some other experiments done while writing the article, can be found in this post in the AutoCAD Architecture Content Discussion Group.
Equal Light Openings With Door/Window Assemblies and Curtain Wall Units
You might think that creating Door/Window Assembly or a Curtain Wall that has equal light openings is a fairly simple task – set up a Division with a fixed number of Cells and you should be good to go. The same technique should also work if you wanted to use a Curtain Wall Unit to subdivide those equal Cells with “muntins” to get equal light openings between muntins. You could then place the Door/Window Assembly or Curtain Wall at any size and have equal light openings. While you can achieve the desired results, it will take a little knowledge and some additional effort.
There are two reasons why it is not quite as simple as we might like:

If you keep the above in mind, it is possible to create equal light openings, and we will take a look at some techniques to do so, starting with the outer Door/Window Assembly or Curtain Wall, and then looking at the impact those choices have on a nested Curtain Wall Unit. A Door/Window Assembly will be used for these examples, but the techniques also apply to Curtain Walls.
There are several ways to generate equal light openings in the parent Door/Window Assembly or Curtain Wall.

For a Simple Panel, Door or Window Infill, using the Start/End Division Offset method is the way to go, as these elements will be sized to fit the light opening of the Cell in which they are placed. If you can achieve your desired Muntin pattern by using the Muntins in a Window Style, that may be the best way to get equal light openings in a style that works for any overall Frame dimension, using a single Infill style.

If you need the greater control over spacing that using a Curtain Wall Unit for Infill can provide, there is a small problem with using the Start/End Offset method – the applied offset makes the outer Cells wider, but does not move the grid lines from the outside edge of the Frame, so the same Curtain Wall Unit Style can not be used for all Cells. (The Mullion Offsets method may also have the same problem, because the light opening is likely not centered on the gridlines in all of the Cells.) Fortunately, two copies of that Curtain Wall Unit Style, one with a Division Start Offset and one with a Division End Offset equal to the Offsets applied to the parent object can be quickly created, assigned to an Infill and used in the Start Cell and End Cell respectively. This gives you the look you want, while maintaining the flexibility of being able to change the overall Door/Window Assembly dimensions.

Here is an example of a more complex muntin pattern. A series of nested grids, all using a fixed number of Cells, was used to create the pattern. Start and or End Offsets were applied as needed to get the equal light openings shown. This can be a little tricky to set up, since the nested grids for the Start and End Cells also need to have offsets applied, but once you have it set up, you can create a Door/Window Assembly with any overall length and height and maintain equal light openings.

Equal Light Openings With Door/Window Assemblies and Curtain Wall Units
You might think that creating Door/Window Assembly or a Curtain Wall that has equal light openings is a fairly simple task – set up a Division with a fixed number of Cells and you should be good to go. The same technique should also work if you wanted to use a Curtain Wall Unit to subdivide those equal Cells with “muntins” to get equal light openings between muntins. You could then place the Door/Window Assembly or Curtain Wall at any size and have equal light openings. While you can achieve the desired results, it will take a little knowledge and some additional effort.
There are two reasons why it is not quite as simple as we might like:
- The “equal” in equal Cells refers to the distance between grid lines. Unless offsets are applied to the Frame or Mullion, the outer grid lines occur at the outside edge of the Frame, while the inner grid lines are centered on the Mullions. This means that the light opening of the start and end Cells will be reduced by the full width of the Frame, plus half the width of a Mullion, while interior Cells will only be reduced by the width of a Mullion. If both Frame and Mullion are the same width, the Start and End Cells’ light opening will be less than the light opening of the Middle Cells.
- The grid lines of a nested Curtain Wall Unit are spaced evenly, based on the location of the parent Door/Window Assembly or Curtain Wall grid lines bounding that Cell, not on the light opening of that Cell. The Frame of the Curtain Wall Unit will be located at the light opening of the Cell, but the locations of “equal Cell” Mullions may not generate equal light openings in the Start, End, Top or Bottom Cells.

Figure 1
Equal Cell Door/Window Assembly with Equal Cell Curtain Wall Unit Infill
Blue Dimensions – Gridlines; Red Dimensions – Light Openings (Typical in all Figures)
Equal Cell Door/Window Assembly with Equal Cell Curtain Wall Unit Infill
Blue Dimensions – Gridlines; Red Dimensions – Light Openings (Typical in all Figures)
If you keep the above in mind, it is possible to create equal light openings, and we will take a look at some techniques to do so, starting with the outer Door/Window Assembly or Curtain Wall, and then looking at the impact those choices have on a nested Curtain Wall Unit. A Door/Window Assembly will be used for these examples, but the techniques also apply to Curtain Walls.
There are several ways to generate equal light openings in the parent Door/Window Assembly or Curtain Wall.
- Frame Offset: This might be acceptable for a Curtain Wall, since it does not create its own opening, although the Curtain Wall’s overall length and height will not represent the overall Frame dimension. For Door/Window Assemblies that are anchored in a Wall, offsetting the Frame pushes it into the Wall, leaving part of the Frame buried in the Wall, which is not acceptable.
- Mullion Offsets: By creating multiple Mullions with varying offsets, assigned to the proper locations, equal light openings can be created. For example, three equal openings can be created when the Frame and Mullion widths are equal by setting up a vertical Division with three equal Cells and then creating two Mullions, each offset by 1/6 of their width toward the middle, resulting in each Cell losing 1-1/3 of the Frame/Mullion width. This can get rather complex when there are five or more equal openings to be created.
- Start/End Division Offsets: This is the easiest method, and can also accommodate the case where the Frame and Mullion dimensions are not equal. Simply subtract one half the width of the Mullion from the Frame width and use that for both the Start Offset and the End Offset of the Division. This will make the Start and End Cells wider than the Middle Cells, resulting in equal light openings no matter how many Cells are specified, without the need to create offset Mullions.

Figure 2
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
For a Simple Panel, Door or Window Infill, using the Start/End Division Offset method is the way to go, as these elements will be sized to fit the light opening of the Cell in which they are placed. If you can achieve your desired Muntin pattern by using the Muntins in a Window Style, that may be the best way to get equal light openings in a style that works for any overall Frame dimension, using a single Infill style.

Figure 3
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Window Style Infill with 0 Width Frame and 1 Width Sash and Muntins
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Window Style Infill with 0 Width Frame and 1 Width Sash and Muntins
If you need the greater control over spacing that using a Curtain Wall Unit for Infill can provide, there is a small problem with using the Start/End Offset method – the applied offset makes the outer Cells wider, but does not move the grid lines from the outside edge of the Frame, so the same Curtain Wall Unit Style can not be used for all Cells. (The Mullion Offsets method may also have the same problem, because the light opening is likely not centered on the gridlines in all of the Cells.) Fortunately, two copies of that Curtain Wall Unit Style, one with a Division Start Offset and one with a Division End Offset equal to the Offsets applied to the parent object can be quickly created, assigned to an Infill and used in the Start Cell and End Cell respectively. This gives you the look you want, while maintaining the flexibility of being able to change the overall Door/Window Assembly dimensions.

Figure 4
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Curtain Wall Unit Style Infill – Three Similar Styles:
1.5 Start Offset in Start Cell, No Offsets in Middle Cell, 1.5 End Offset in End Cell
(3.5 Offset Top and Bottom at Horizontal Division, All Three Styles)
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Curtain Wall Unit Style Infill – Three Similar Styles:
1.5 Start Offset in Start Cell, No Offsets in Middle Cell, 1.5 End Offset in End Cell
(3.5 Offset Top and Bottom at Horizontal Division, All Three Styles)
Here is an example of a more complex muntin pattern. A series of nested grids, all using a fixed number of Cells, was used to create the pattern. Start and or End Offsets were applied as needed to get the equal light openings shown. This can be a little tricky to set up, since the nested grids for the Start and End Cells also need to have offsets applied, but once you have it set up, you can create a Door/Window Assembly with any overall length and height and maintain equal light openings.

Figure 5
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Curtain Wall Unit Style Infill with Offsets Applied to Multiple Divisions as Necessary
Equal Cell Door/Window Assembly with 1.5 Start and End Offset
Curtain Wall Unit Style Infill with Offsets Applied to Multiple Divisions as Necessary
Labels:
AU Online,
Curtain Wall Unit,
Door/Window Assembly
May 06, 2009
Vote for AU 2009 Sessions
Public voting on the sessions that have been proposed for Autodesk University 2009 is now open. You do need to be registered with the AU Online site in order to participate. Go to this page and login using you AU Online user name and password. An access code is not required for public voting. You can submit votes (including comments) on up to twenty sessions. But hurry - there are a lot of session descriptions to read through (even if you limit yourself to the software you use or the topics that interest you) and the voting deadline is this Friday, May 8, at midnight, US Pacific Daylight Time.If you are planning to attend AU 2009, here is your chance to influence what will be offered. If you can not attend this year, you can still offer your opinion. There will be a "Virtual AU" this year as well, where those who can not attend in person will, for a fee (no information on the cost on the AU Online site as of yet), be able to view virtual sessions that will be video recorded at AU 2009. These sessions will also be "broadcast" at AU, so physical attendees will also have a chance to see them.
Not registered on the AU Online site yet? It is free, and gives you access to AU year-round from your desktop. You can easily create an account here. If you (or your firm) are on Subscription, register through the Subscription website, for access to more (and more recent) AU content.
January 01, 2009
AU Online Abandons Single Sign-in
Less than four months after launching the "single sign-in" for all Autodesk Websites, the recent relaunch of the AU Online site has resulted in that part of the Autodesk web presence abandoning the single sign-in.
I used the feedback link on the AU Online site to question why the single sign-in had been abandoned. After the first reply indicated that the single sign-in was still valid for AU Online, I provided a more detailed description of what that meant (one sign-in for all sites/once signed in at one, moving to any other does not require signing in again), I was told that the single sign-in was removed due to a large amount of attendee feedback against it.
While I suppose I should applaud Autodesk for listening to the users, I have to question who would be against this? I would emphasize that there is a difference between being against the way it was implemented and being against the concept in general.
Yes, I was annoyed by the way it was implemented and by the spotty initial performance, complicated by rolling out a new format for the web-based Discussion Groups at the same time. Yes, I miss my old five-character password, now bloated to eight characters with at least one upper case letter and one numeral, because each additional character geometrically increases the probability that I will mistype the password. But with the single sign-in system, at least I could sign in once and visit the Discussion Groups, AU Online and the Subscription site. Now, I still have the eight-character password AND I have to sign in separately at AU Online.
So the question remains - who would want to sign in multiple times? Disconnecting the AU Online site from the single sign-in did not resolve any of the initial problems I had with the implementation - were there any other, ongoing issues? If anyone had a problem with the whole concept, what prevented them from simply signing out when leaving one site, then sign back in on the next?
I have to think that the real issue here was one of either not having time or not wanting to expend the effort to integrate the new AU Online site with the single sign-in, rather than responding to meaningful user feedback.
I used the feedback link on the AU Online site to question why the single sign-in had been abandoned. After the first reply indicated that the single sign-in was still valid for AU Online, I provided a more detailed description of what that meant (one sign-in for all sites/once signed in at one, moving to any other does not require signing in again), I was told that the single sign-in was removed due to a large amount of attendee feedback against it.
While I suppose I should applaud Autodesk for listening to the users, I have to question who would be against this? I would emphasize that there is a difference between being against the way it was implemented and being against the concept in general.
Yes, I was annoyed by the way it was implemented and by the spotty initial performance, complicated by rolling out a new format for the web-based Discussion Groups at the same time. Yes, I miss my old five-character password, now bloated to eight characters with at least one upper case letter and one numeral, because each additional character geometrically increases the probability that I will mistype the password. But with the single sign-in system, at least I could sign in once and visit the Discussion Groups, AU Online and the Subscription site. Now, I still have the eight-character password AND I have to sign in separately at AU Online.
So the question remains - who would want to sign in multiple times? Disconnecting the AU Online site from the single sign-in did not resolve any of the initial problems I had with the implementation - were there any other, ongoing issues? If anyone had a problem with the whole concept, what prevented them from simply signing out when leaving one site, then sign back in on the next?
I have to think that the real issue here was one of either not having time or not wanting to expend the effort to integrate the new AU Online site with the single sign-in, rather than responding to meaningful user feedback.
Subscribe to:
Posts (Atom)